- 您现在的位置：买卖IC网 > Sheet目录1001 > PR33MF11NSZF (Sharp Microelectronics)RELAY SSR 240VAC .3A 8-DIP
PR23MF11NSZ Series
PR33MF11NSZ Series
■ Design Considerations
● Recommended Operating Conditions
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Input
Input signal current at ON state
Input signal current at OFF state
I F (ON)
I F (OFF)
?
?
20
0
25
0.1
mA
mA
Load supply voltage
PR23MF11NSZ
PR33MF11NSZ
V OUT (rms)
?
?
120
240
V
Output
Load supply current
I OUT (rms)
Locate snubber circuit between output terminals
(Cs = 0.022 μ F, Rs = 47 ? )
?
I T (rms) × 80%( ? )
mA
Frequency
Operating temperature
f
T opr
?
?
50
? 20
60
80
Hz
?C
( ? ) See Fig.2 about derating curve (I T (rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (I F ) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (I F ) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V D , increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs = 0.022 μ F and Rs = 47 ? . The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
Sheet No.: D4-A00301EN
9
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PR33MF51NSZF
RELAY SSR TRIAC OUT 300MA 8-DIP
PR36MF11NSZF
RELAY SSR 240VAC .6A TRIAC 8-DIP
PR36MF22NSZ
RELAY SSR 240VAC .6A ZC 8-DIP
PR39MF11NSZF
RELAY SSR 240VAC .9A TRIAC 8-DIP
PR39MF51NSZF
RELAY SSR 240V 0.9A 8-DIP
PR3BMF51NSKF
RELAY SSR 10MA 240V 1.2A 8-DIP
PRDA-11AJA-120
RELAY GEN PURPOSE DPDT 20A 120V
PRGD48150-10
RELAY SSR DC 480V RANDOM PNL MNT
相关代理商/技术参数
PR33MF11YIPF
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF11YSZF
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF51NIPF
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF51NSZF
功能描述:固态继电器-PCB安装 SSR DIP6 10mA 600V 150mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
PR33MF51YIPF
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF51YPLF
制造商:Sharp Microelectronics Corporation 功能描述:PR33MF51YPLF - Tape and Reel 制造商:Sharp Microelectronics Corporation 功能描述:RELAY SSR 240V 制造商:Sharp Microelectronics Corporation 功能描述:Solid State Relay 8 Pin 600 Volt
PR33MF51YSZF
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Non-Zero Cross type DIP 8pin Triac output SSR
PR-33-REFLECTOR
制造商:TE Connectivity 功能描述:9-1197714-8